Increase the performance of your PCs : BIOS Settings

“Increase the performance of your PCs with BIOS settings. ”

The BIOS – Basic Input Output System – is software on the mainboard of your computer. It ensures that the hardware components of it work and interact flawlessly.
When the pc starts, the BIOS calls up the OS .

You can check or adjust settings via menu.
Even minimal adjustments you can optimize the performance of your PCs or laptop.

The settings are saved on a permanent memory in order that changes remain even without power or switched off device.

The newer version of the BIOS is named UEFI – Unified Extensible Firmware Interface.
It is mostly used with 64-bit processors and offers functions almost like the BIOS.

Unlike the BIOS, the UEFI are often controlled with the mouse rather than the keyboard.
Open BIOS
Opening the BIOS differs depending on the motherboard manufacturer.
The device needs to be restarted each time. Before and through the restart, a particular key must be pressed to open the configuration.

The following overview shows you which of them key you would like to call up the BIOS :

Manufacturer button
Asrock F2 or Del
Asus F2 or Del
Dell F2
Gigabytes Dist
Intel F2
Lenovo F1
Medion F2
MSI Dist
Samsung F2

Open BIOS settings

  1. Turn off the PC or laptop
  2. Hold down the button
  3. Switch the device on again

Open UEFI BIOS in Windows 10

  1. Hold down the Shift key
  2. Click the Restart option in the Windows menu

Reset: Reset BIOS settings

If you have made settings in the BIOS that you no longer want to use or problems have arisen due to changes, you can reset them.

The following three options are available for a reset:

BIOS settings

Open the BIOS settings. select the menu item Load Setup Defaults (or similar).
The BIOS settings are reset to the factory settings.
Possibly. you must then make settings again, for instance with reference to the graphics card.

Jumper

If the pc not boots up, the BIOS settings can be reset using a jumper (a kind of plug).
To do this, turn off the device, disconnect it from the power supply and set the plug to position 2. After a brief time, move the jumper back to its starting position.
After restarting the BIOS should open with the default settings.

Remove the battery

The last resort is to remove the battery for the BIOS. to do this, first turn off the device. Remove the battery on the mainboard – wait up to an hour before putting it back in.
Change and save BIOS settings
First open the BIOS as described above. Make the changes.
Save the changes with the F10 key. If you do not want to apply the changes, use Esc.

Interesting Article : How to Convert your Non Apple Pc into Apple Mac (Ubuntu OS) ?

Helpful and recommended settings: Optimize BIOS

We present 9 settings with which you’ll be able to optimize the BIOS and also the performance of your PCs and computer.
Please note that, depending on the motherboard, the designations for the options that can be made in the BIOS settings may differ from the subsequent recommendations:

Change BIOS boot order

In the boot menu you’ll specify from which hard disc , partition or from which data carrier (USB, CD, etc.) you want to start / boot the computer.
This can be particularly useful when installing an OS from the USB stick.

Open the boot menu and alter the order

  1.  switch off the PC or laptop
  2.  Press and hold the key to open the BIOS
  3.  Switch the device on again
  4. The BIOS opens
  5.  Press the key consistent with the following table to call up the boot menu
  6. Select the data carrier or the OS with which you want to start in the future
Manufacturer button
Asrock F11
Asus F8 or Esc
Dell F12
Gigabytes F12
Intel F10
Lenovo F12
Medion F10
MSI F11
Samsung Esc

USB configuration

  • Under USB Configuration you can use USB Device to set whether you use USB or not. Again, you can improve the performance of your PCs and computer by specifying only the resources you need.
  • Activate EHCI (USB 2.0) under USB Configuration.

Decrease boot time

Go to the boot menu. Set the partition / disk drive you’re using to Enable, the remaining unused ones to Disable.
The computer should now boot / start faster.

Save electricity

Select Power (or similar) from the submenu.

Activate the ACPI APIC support using Enabled. If you’re using 64-bit, you ought to choose ACPI 2.0 support instead.
Under Suspend Mode you’ll set what proportion power you would like to save lots of . With S1, for instance , the disk drive and monitor are in sleep mode when the pc isn’t in use.
The power consumption should now be lower.

Interesting Article : These killing features make your phone a super smartphone.

Check CPU

For this setting, attend the Hardware Monitor option.
The temperature of the processor is displayed under CPU Temperature. make sure that it doesn’t exceed 60 degrees.
At this point you can set the speed of the fans. Because increased temperatures cause a reduction in work performance.

Start up PC automatically

If you use your computer at about an equivalent time a day , you can have it start automatically using the BIOS.
Select the Advanced menu item – under RTC Alarm you can set the start time.

Adjust graphics card

Under Advanced you can use PEG Link Mode to line the performance of the graphics card to different levels. Here you’ll reach your goal by trying it out.
If you use another graphics card additionally to the already integrated graphics card, this can cost time and performance when booting. Avoid this and determine which graphics card is to be used under Integrated Peripherals.

Optimize RAM

Normally the BIOS recognizes the optimal clock frequency of the built-in main memory by itself. If you still want to make changes, you’ll find what you’re trying to find in the Advanced menu item, where you’ll adjust the RAM configuration.
However, laypeople should take care here as they will easily damage the hardware.

Protect the BIOS with a password

This can be protected with a password under Main or the standard settings in the BIOS. The settings can be found under Security.

Set up SSD and make BIOS settings

SSD hard drives speed up your work processes on the PC immensely. If you propose to install or use an SSD disk drive , you ought to make optimal use of the SSD’s performance.

To do this, set the mode to AHCI (Advanced Host Controller Interface) in the BIOS settings under Integrated Peripherals.

Computer Optimization is tricky things but using above tips you can increase the performance of your PCs. But keep this in your mind always that the configuration of computer is very important. If you’re using high end PCs then the optimization is easy and very clear but if you’re using low end PCs then It may be possible that you’ll not get desired result.

Do you like Aashish's articles? Follow on social!
Comments to: Increase the performance of your PCs : BIOS Settings

Your email address will not be published. Required fields are marked *

Login

welcom
....

You can make anything by Reading and Writing.
Join Aranjra